|

How to Change Units on Bushnell Tour V4 Rangefinder

ByMichael Reeves

← Golf Equipment | Golf Accessories & Apparel


BLOCKQUOTE_0

Quick answer

  • Hold the Mode button until the unit display flashes.
  • This toggles between yards (YDS) and meters (M).
  • It’s a straightforward process, just takes a steady hand and knowing which button to push.

Who this is for

  • Golfers who need to switch their Bushnell Tour V4 between yards and meters for different courses or international play.
  • Anyone new to the Tour V4 or who accidentally changed the unit setting and needs to revert to their preferred measurement.

What to check first

  • Battery Level: Make sure your Bushnell Tour V4 has a good charge or fresh batteries. A low battery can cause all sorts of weird glitches, and you don’t want it dying mid-round.
  • Button Location: Get familiar with the Power and Mode buttons. They’re usually right there on top, easy to access. You don’t want to be fumbling around on the course trying to find them.
  • Current Unit Display: Take a quick look at the screen. Is it currently showing yards (YDS) or meters (M)? Knowing your starting point makes the change easier.
  • Device Status: Ensure the rangefinder is powered on and in its ready state, not actively scanning or in a menu. This ensures the button press registers correctly.

Step-by-step plan for Bushnell Tour V4 How to Change from Meters to Yards

1. Power Up the Device: Press the Power button to turn on your Bushnell Tour V4.

  • What to look for: The LCD screen should illuminate, displaying the current measurement unit (YDS or M) and ready for use.
  • Mistake to avoid: Trying to change units with the device off. It’s like trying to change gears without the engine running – pointless.

2. Locate the Mode Button: Find the Mode button, which is typically situated near the Power button on the top of the unit.

  • What to look for: It might be labeled with an “M” or have a small icon indicating its function. Refer to your manual if you’re unsure, but it’s usually pretty obvious.
  • Mistake to avoid: Accidentally pressing the Power button again. This will either turn the rangefinder off or initiate a distance scan, neither of which helps you change the unit.

3. Initiate Unit Change Mode: Press and hold the Mode button for approximately 5 to 10 seconds.

  • What to look for: The unit display (YDS or M) on the screen should begin to flash. This flashing is your confirmation that the device is now in unit selection mode. This is the key visual cue.
  • Mistake to avoid: Releasing the button too soon. If the unit doesn’t start flashing, you haven’t held it long enough. Patience is key here, just like waiting for a good putt to drop.

4. Confirm Unit Selection Mode: Once the unit display is flashing, release the Mode button.

  • What to look for: The flashing unit indicates that it’s ready to be toggled. You’ve successfully entered the unit selection sequence.
  • Mistake to avoid: Holding the button down too long after it starts flashing. This might sometimes reset the process or cause unexpected behavior. Catch it when it starts blinking.

5. Cycle Through Units: Now, briefly press the Mode button to cycle through the available units.

  • What to look for: Each short, quick press of the Mode button should toggle the display between “YDS” (yards) and “M” (meters). You’ll see the letters change with each tap.
  • Mistake to avoid: Holding the button down again. A brief press is all that’s needed here. Holding it will likely put you back into the initial 5-10 second hold mode.

6. Lock In Your Desired Unit: Stop pressing the Mode button when your preferred unit (either YDS or M) is displayed on the screen.

  • What to look for: The flashing should stop, and the selected unit should remain steady on the display, indicating that the change has been saved.
  • Mistake to avoid: Not waiting for the display to stop flashing and lock in. Give it a second or two after you stop pressing to ensure the setting is registered.

7. Verify the Change: Take one final look at the display to confirm that the correct unit of measurement is now active.

  • What to look for: The display should clearly show either “YDS” or “M” without flashing.
  • Mistake to avoid: Assuming the change is made without visually confirming. A quick double-check saves you from measuring in the wrong units later.

Bushnell Tour V4 How to Change from Meters to Yards: Common Mistakes

  • Not Holding the Mode Button Long Enough — The unit display won’t flash to indicate it’s ready for selection. This is the most common reason people get stuck. You need to hold that button down until you see the flashing indicator. — Fix: Ensure a firm, sustained press of the Mode button for at least 5-10 seconds until the unit starts flashing.
  • Pressing the Power Button Instead of the Mode Button — This will either turn the device off or initiate a distance scan, completely bypassing the unit selection process. — Fix: Always use the dedicated Mode button for changing units. It’s a different button for a reason, so make sure your thumb finds the right one.
  • Briefly Pressing the Mode Button When Trying to Hold It — Sometimes, in the attempt to hold the button, people might accidentally tap it first, which can either do nothing or rapidly cycle through other modes without entering the unit selection menu. — Fix: Approach the Mode button with a deliberate, sustained press from the start. Don’t tap it first; just press and hold.
  • Not Confirming the Change Visually — You might think you’ve successfully changed the unit, but if you don’t wait for it to lock in or double-check, it could revert back or stay the same, leading to confusion on the course. — Fix: After the unit stops flashing, take another look at the display to confirm the correct unit (YDS or M) is showing before putting the rangefinder away.
  • Trying to Change Units While Actively Scanning — The rangefinder needs to be in a stable, ready state to accept this kind of setting change. Attempting it while in the middle of measuring a distance can lead to unexpected results or no change at all. — Fix: Turn the device on, wait for it to show a stable reading or ready indicator, and then proceed with the unit change procedure.
  • Assuming the Device is Ready — Sometimes, even after powering on, the device might still be processing something internally. Rushing the button press can lead to errors. — Fix: Give the rangefinder a second or two after powering on before you start holding the Mode button. This ensures it’s fully booted and ready for input.

FAQ

  • How do I turn on my Bushnell Tour V4?

Simply press the Power button located on the top of the device. The screen will light up, and you’ll see the current display ready for use.

  • What is the purpose of the mode button on the Bushnell Tour V4?

The Mode button on the Bushnell Tour V4 serves multiple functions. Primarily, it’s used to cycle through different settings, including changing the unit of measurement between yards and meters. It can also be used to select different scanning modes or flagstick modes, depending on the specific model features.

  • Can I switch between meters and yards on the Bushnell Tour V4?

Yes, absolutely. The Bushnell Tour V4 is designed to allow you to switch between yards (YDS) and meters (M). This is a crucial feature for golfers who play on courses with different measurement systems or who travel internationally. You can find more detailed information on Bushnell Tour V4 Units Conversion here.

  • How do I know if my Bushnell Tour V4 is currently set to yards or meters?

It’s quite straightforward. The unit of measurement is clearly displayed on the LCD screen. If you see “YDS,” it’s set to yards. If you see “M,” it’s set to meters.

  • What if the units don’t change after I hold the mode button?

If the unit display isn’t flashing after holding the Mode button for about 10 seconds, first double-check that you’re pressing the correct button. If you are, try holding it for a few seconds longer. Sometimes, a simple power cycle – turning the device off and then back on again – can also resolve minor glitches. For more general troubleshooting tips on Bushnell rangefinders, you can check out guides on Changing Units on Bushnell Rangefinder here.

  • Do I need any special tools to change the units on my Tour V4?

No special tools are required. The unit change is done entirely through button presses on the rangefinder itself. Just make sure your device has sufficient battery power.

  • Can I set different units for different modes on the Tour V4?

No, the unit setting (yards or meters) is a global setting for the device. Once you change it, it applies to all modes and functions of the rangefinder until you change it back.

Sources:

Similar Posts